But for the time being, I just want to show how I make shisha charcoal briquette machine. Perhaps Bridge has made some charcoal in the past, or perhaps he will make some other content in the future. My still will benefit from the addition of charcoal.
It was constructed quite some time ago, but in reality, all it is is a drum, and as you can see, it has the capability of closing off the top. I have no doubt that other content will contain the same things. They are virtually identical. What I did was drill a few holes on this side, but I made sure to keep them all aligned in the same direction. I use this cover so that I can be certain of the location of the line at all times. When I place it in the flames, I am confident that it will point downward. As soon as the gas begins to flow out, it will enter the fire and contribute to its continued growth.
Do you have any idea how well it burns? This is another important aspect of the show. It is known as a fire pit by us. It is essentially a bucket with a capacity of 55 gallons. The other piece, which is essentially a divider, does so into two equal parts. Simply putting the two halves on top of each other will do.
There are some walking sticks for refrigeration that simply remove it from the center. These can be thought of as chimneys in this context. My Alps are formed by the movement of air. In general, I will put some belts and metal belts, and when I put the drum on top of everything, it will be on fire, but it will be on fire. This is how it should be positioned. You can see that there is some room at the bottom; consequently, I will be able to place some wood there in order to keep the fire going. As I mentioned earlier, the cover's sole purpose is to indicate to me the location of the hole in the side of the drum that is located at the bottom of the tank. As a result, all of the gas will now flow directly into the fire.
They have a healthy fire going, so let's just hang out here for a little while and let it do its thing. As soon as I am certain that everything, including the wood, is in its proper place, I will place the drum atop it and then cover it with the top cover. Our fire is almost doing a good job of burning. It is my assumption that you are aware that in order to make charcoal, the wood must be burned in an atmosphere devoid of oxygen in a top barrel. This is what winds up occurring.
Only a few of the holes at the bottom have been sealed off, allowing all of the gas and pressure to escape and ensuring that homemade bombs will not detonate. At this point, all we have to do is wait for a few more hours. I mentioned that, or the three hours. The bottom fell out of sight as soon as I became aware of all the gas explosions.
It ought to be finished almost entirely now. Now that everything is ready, I'm going to put the lid on it so that the heat can be contained inside the drum for as long as possible. As was the case with the barrel, our current perspective is severely limited. There is a small amount of smoke produced by the chimney stool, but once the fire is fully lit and comfortable, there will be very little smoke produced by this small amount of smoke. I can make out a fire burning, but the interior is not all that dim.
Esther, it has only been three hours, but we will look into it. They have been ablaze for roughly ten minutes at this point. As can be seen, they have been burning for close to ten minutes without producing any visible smoke. You can see that there are some fires burning inside, and at this point all that needs to be done is wait for it to be completed.
After approximately half an hour, you will notice that there is significantly less smoke. I'm going to speak into the microphone. If you are able to use their voice, the gas will come out and burn. Although I cannot confirm this, I believe the camera will be able to capture charcoal making machine supplier in approximately three hours. After that, you will be able to view the guess.
It has quieted down quite a bit, which indicates that it will soon be over, and I believe that everything will turn out all right in the end. Do not panic. That is to say, it won't be warm for another seven and a half hours. It is possible for us to open it and examine its contents. Okay, this wraps up everything nicely.
Now remove the o-ring that was sealing the container. Since it is now the following day, everything has become more comfortable, as of a few hours ago. It is obvious that the transformation has taken place, so all of these components must now be reduced to powder. Beginning on that day, we will proceed with the instructional content regarding the production of coal. I will explain to you how I am able to do it effectively. When it is ready to be placed on the support, the charcoal that has been crushed or ground into a finer consistency looks like this. After we have completed the coal-making process, we look like this.
This is how they look when they first emerge from their shell. There are also some pityriasis that are more severe. Because they are not useful in any way, I have no problem making use of all of these. They simply grind everything up, as it is more convenient to use charcoal, and then they spend their time and effort making prickles.
When you have charcoal, there are only two good pieces of charcoal available to you. It's not really practical to use. What do you use to make coal, if I understand correctly? It goes without saying that charcoal is extremely dry, brittle, and loose. There isn't much room for compression there.
Oh, it doesn't mix very well with water, so what we need to do is take some flour, also known as starch, and boil it for a short period of time. After that, we add it to this, mix it, and when it dries, it will burn together to create a solid mass. To continue, then, this will be the next step. Next, we add flour, which can be utilized in the preparation of baked goods such as bread and cake, to a fairly large casserole dish. I use two cups, but I thought one, ours, or even two, should be sufficient for the entire batch. To prevent it from clumping together in the water, you simply need to stir it.
That is to say, we can boil it at a later time, and at that point, you will notice the difference. At this point, all that's happening is a misleading boiling. It goes without saying that you need to stir it quite frequently to prevent it from catching fire. The appearance is essentially the same as this.
Simply pour some in this area and mix it up; that's how it should look. Because we need you to be prepared for hot molding, we will wait until it has cooled down before proceeding. The texture is close to being finished. This allows you to shape it without having to worry about it spreading. The molding process is the next step.
At this point, I have three short moldy PVC pipes, each measuring 50 millimeters in length. As a result of Raff Katia removing the leaves, I can now only get the impression that these three are the same. The first one is in our possession. Yes, we do also have the other one, which is a much rougher version. You simply have to put the filling mold back together.
It is possible to have it in any size you desire at your request. The procedure is exactly the same. So we have made six. It's possible that, much like the manito serve, we want to purposely make it weak. You can. We have accomplished a great deal. The quantity of the first batch I produced is slightly greater than the quantity of the second one I needed to produce.
